Blend well where the light turquoise meets the dark turquoise to get a nice, even transition between the two colors. Remember, there's no wrong or right - add and adjust until you see the color you're happiest with.Īpply the lighter turquoise to the remainder of the canvas. Once again, Rebecca adjusted her color, adding a little white to increase the opacity and richness. Next, pour the light turquoise: this will represent the shallow water closer to shore. In this case, Rebecca wanted a more saturated color so added more turquoise for a deeper, richer look. If you want to increase the opacity, add a little bit of white.If you want the color a bit darker, add more turquoise.) Use your plastic knife to spread it out and over the sides.įeel free to adjust the color as you wish: Next, we're going to start building our ocean, starting with the dark turquoise to represent the deepest, darkest part of the water.Īpply the dark turquoise to about half of your panel, s tarting on the far end ( the side opposite to the sand. If you're using a round panel, apply the sand to the edge closest to you, spreading the resin out and over the sides with a popsicle stick or a plastic knife. Never add more than 6% of the total volume of resin and hardener combined, or your resin won't cure.Ĭheck the transparency by using the mixing stick to pull some of the tinted resin up the side of your cup: if the tint is too translucent, add a little more until you're happy with what you see.Īfter your tinted resin has had a chance to sit and thicken, you're ready to pour.įirst, start with the sand color to create the beach. ResinTint is a highly saturated pigment based colorant, so it's always best to start with less than you need, adding more as necessary. sand ( neon green, neon pink, neon yellow & white mixed together ).dark turquoise ( using several drop of turquoise for a deeper color ).light turquoise ( using only a few drops of turquoise and a bit of white ).If you try to pour right after mixing, the resin will be too fluid: you'll end up with muddy colours and could lose your design. After you mix in the tint, ensure the resin sits and thickens for 15 minutes before you start to create your design. Don't be afraid to mix and match to achieve the colours you wish to use. Shake the ResinTint bottles well and use a few drops to tint each cup of resin, mixing well after each addition. Divide the resin equally among small plastic cups, allowing one per color. Measure equal amounts, by volume, of resin and hardener and mix thoroughly for at least 3 minutes, scraping the bottom and sides of the mixing container as you go. If you want to allow your resin to run over the sides of your panel, prop it off of your work surface: we like using painter's pyramids, plastic cups or lego blocks. If you want to keep the panel edges clean, tape them off with painter's tape to protect them from getting splashed with resin. Gather your tools so that everything is on hand before you start, including your dust cover. 1. Assemble Your Materials Before You Start: dust cover large enough to cover your pieceīrowse our resin art accessories & tools.plastic stands to prop your work up on ( painter's pyramids or plastic cups ).a piece of plastic to work on ( a cut piece of vinyl shower curtain works great ).small plastic cups and stir sticks, enough for each colour of tint used.Whether you call it ocean art, beach art or a seascape, chances are you've seen this gorgeous look before and wondered how it was done: artist Rebecca Brianceau dropped by the ArtResin studio to demonstrate how easy it is to create your own stunning ocean art, even for a beginner! Layering various shades of tinted ArtResin creates a feeling of motion and depth: beautiful, deep ocean blues contrast with white wave crests against a sandy shore and ArtResin's irresistibly shiny finish makes you want to dive right in. Resin is essential to creating realistic ocean art: its clarity, consistency and gloss replicate the look of water in a way you simply can't get with any other medium. The secret to creating beautiful, realistic beach resin art is tinted epoxy resin and a hairdryer: it's an easy technique that involves pouring layers of resin in various shades of blue, then finishing with a layer of white that gets pushed around with a hairdryer to create a lacing effect reminiscent of sea foam.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |